It's time for new YT video!
spacedrone808
Posted 2021-11-02 4:13 AM (#2295)
Subject: It's time for new YT video!



UMC U5S

Posts: 55
2525
High Treason channel almost 3 months w/o any new video.
It is quite prohibited, don't you think so?

Top of the page Bottom of the page
spacedrone808
Posted 2022-03-26 6:39 PM (#2349 - in reply to #2295)
Subject: Re: It's time for new YT video!



UMC U5S

Posts: 55
2525
Finally, a new video has landed:
https://www.youtube.com/watch?v=iBcijZ-CiLg

High Treason, thank you so much!

Writing here, because i don't have YT account to do comments.
Top of the page Bottom of the page
DXZeff
Posted 2022-03-26 8:29 PM (#2350 - in reply to #2349)
Subject: Re: It's time for new YT video!



TM Crusoe

Posts: 618
500100
Location: Hull, UK
Took fucking long enough. Here's hoping there's not too much more bullshit goes on to get in the way for a while, though I'm still wrestling with the process of modern software to no end.

Anyways, much appreciated.

Edited by DXZeff 2022-03-26 8:30 PM
Top of the page Bottom of the page
spacedrone808
Posted 2022-03-26 11:29 PM (#2351 - in reply to #2350)
Subject: Re: It's time for new YT video!



UMC U5S

Posts: 55
2525
DXZeff - 2022-03-26 8:29 PM

Took fucking long enough. Here's hoping there's not too much more bullshit goes on to get in the way for a while, though I'm still wrestling with the process of modern software to no end.

Anyways, much appreciated.


How modern?
Top of the page Bottom of the page
DXZeff
Posted 2022-03-27 10:28 AM (#2352 - in reply to #2351)
Subject: Re: It's time for new YT video!



TM Crusoe

Posts: 618
500100
Location: Hull, UK
Within the last couple of years. The capture card software seems to be a reskinned OBS or something similar, so it outputs broken files that crash the editor or cause other problems. To fix it, I have to feed the files to FFMPEG and convert them to raw, but this still isn't foolproof and you might even spot missing or jittering frames at the start of certain clips. Incidentally, this also caused Vegas to crash several times when trying to render and a lot of the editing was pretty much blind.
I think in the future I'll just have to accept a hit in quality, as the updated driver for the capture card no longer allows raw capture directly. My only remaining solution is to Fraps the capture window - but now it captures the whole application and not just the capture surface, and there's no borderless option now either - then crop out the UI and everything. Resolution will be low, frame rate will be poor, render times will be extremely long and it's only good until something else comes along to break this method too.
Top of the page Bottom of the page
spacedrone808
Posted 2022-03-27 10:39 AM (#2353 - in reply to #2352)
Subject: Re: It's time for new YT video!



UMC U5S

Posts: 55
2525
ah, i remember you mention OBS in video.
And what kind of video editing software do you use?
Top of the page Bottom of the page
DXZeff
Posted 2022-03-27 10:24 PM (#2354 - in reply to #2353)
Subject: Re: It's time for new YT video!



TM Crusoe

Posts: 618
500100
Location: Hull, UK
Sony Vegas. Used it since it was Sonic Foundry Vegas.

Edited by DXZeff 2022-03-27 10:25 PM
Top of the page Bottom of the page
spacedrone808
Posted 2022-03-28 4:20 AM (#2355 - in reply to #2354)
Subject: Re: It's time for new YT video!



UMC U5S

Posts: 55
2525
Oh, I'm using Vegas 18 [2020], last version to support Win7.
Pretty glitchy, but i think than it is better than adobe premiere.

Edited by spacedrone808 2022-03-28 4:21 AM
Top of the page Bottom of the page
spacedrone808
Posted 2022-12-27 6:28 AM (#2433 - in reply to #2295)
Subject: Re: It's time for new YT video!



UMC U5S

Posts: 55
2525
NEW vid from HT!!
https://www.youtube.com/watch?v=nAuLF4Y7iXA&t=0
Top of the page Bottom of the page